Deluxe Storage Cabinet Specifications |
Materials: Deluxe Storage Cabinets fabricated of high quality, cold rolled carbon steel, free
of scale or rust and fully pickled. Exposed edges, corners and
surface areas are free of sharp edges and all workmanship is of
the highest quality as measured by the industry. |
| |
Finish: All steel components shall be thoroughly cleaned and
phosphatized for rust resistance in a fi ve-stage pre-treatment
process. A high grade of polyester/epoxy powder paint is to be
applied electrostatically with a gloss reading of between 55 and
65. The finish shall have a salt spray rating of 250 hours or more. |
| |
Header: The header is 16 gauge steel, formed into a 1-11/16" wide
and 1-7/16" deep "C" channel formation having a 25/32" angle formation
on the bottom leg of the header. The header is slotted
to accept the lock bar from the three point locking system. The
header is welded to the frame making it an integral part of the
frame assembly. |
| |
Sill: The sill is 16 gauge steel formed into a 4" wide and 1-3/16" deep
"C" channel formation having a 13/16" angle formation off the top
leg of the sill. The sill is slotted to accept the lock bar from the
three point locking system. The sill is resistance welded to the
frame making it an integral part of the frame assembly. |
| |
Side Frames: The side frames are 16 gauge steel formed into 1"
wide "C" channel formation have a 1-1/2" and a 21/64" flange. The
side frames are resistance welded to the header and sill. |
Hinges: Hinges are semi-concealed, five knuckle, tight pin, 16 gauge
full loop hinges that are resistance welded to frames and riveted
to the door. There are 4 hinges per door on 78" cabinets and 3
hinges per door on 42" cabinets. |
| |
Doors: Doors are formed from 21 gauge steel with a 27/32" flange on
top and bottom. The doors are 1" thick with a channel formation
on the edges. The door strike on the left hand door is hemmed
for a smooth uniform edge. The doors are reinforced with a full
length door stiffener that is 41/8" wide and 25/32" high. The doors
are designed in such a way to accept the standard three point
locking system. |
| |
Sides: Sides are formed from 22 gauge steel and have 3/4" 90 degree
flanges on the top and the bottom. The sides have a 90
degree fl ange on the back for strength and an offset on the front
to allow the side to fi t fl ush with the frame. Each side has a dog
ear strip to secure the shelves in place and allow for shelf adjustability
on 2" centers. |
| |
Back: The back is formed using 22 gauge steel and has 25/32" 90 degree
flanges on the top and bottom. Welded cabinet backs have
two, 4-11/16" x 2-3/4" louver clusters for ventilation, while KD backs
have four. Each louver is formed to the inside of the cabinet with
nothing protruding to the back of the cabinet. The backs have
2 rows of dog ear lances perforated in the back to secure the
shelves and allow shelf adjustability on 2" centers. Every third dog ear is shaped different
to make installation and line up of
shelves easier. |
| |
Top: The top is formed using 22 gauge steel and has 25/32" 90
degree flanges on all four sides. |
| |
Bottom: The bottom is formed using 20 gauge steel and has 25/32"
flanges on all four sides. |
| |
Shelf: 18" Shelves are 20 gauge, 24" Shelves are 22 gauge,
flanged at rear and ends. Box formation at front. Adjustable
on 2" increments. |
| |
Handles: The cabinet has 2 brushed chrome handles. The
right handle has a built in lock and locks both doors, making
the opening and closing of dual swing out doors easy. The left
dummy handle provides a pull for the door while giving an attractive
appearance to the cabinet. The locks are core removable
and master keyed. Locks can be keyed to the same key. |
| |
Recessed Handle Units: 3-1/2" diameter recessed handle with
built-in lock on right hand door. |
| |
Three Point Locking System: The cabinet is equipped with a
secure three point locking system. The system consists of a
lock cam that secures the 2 doors together and 2, 5/8" x 1/8"
locking bars that locks the right door securely into the header
and sill. The left door is held by the right door. The lock mechanism
is operated by turning the right handle and the two lock
bars operate smoothly using nylon silencers. |
| |
Partition: Partitions are formed using 22 gauge steel and have
25/32" flanges at top, bottom and rear with a formed bead in
the front. The partitions have 2 rows of dog ear lances running vertical, designed to secure the shelf in place. |
| |
Partition shelves: Partition shelves are formed with 22 gauge steel
and have 1-1/8" flanges at rear and ends. They have a channel
formation in front and are adjustable on 2" increments. |
| |
Shelf Strip: Shelf clips are formed using 20 gauge steel. No hardware
is required to hold shelf. |
| |
Coat Rod: Coat rod is made using 20 gauge x 5/8" O.D. plain
steel tubing. Coat rods are installed into combination cabinets
through coat rod brackets and secured with hardware screws
on top of bracket and side. |
| |
Coat Rod Brackets: Coat rod brackets are formed with 20 gauge
steel. Coat rod brackets bolt to the side panel and partition with
8-32-1/2" bolts and nuts. |
| |
Bolts & Nuts: For KD cabinets only: Bolts and nuts consist of
a sealed plastic bag with #8-32-1/2" slotless headed bolts with
hex nuts. All bolts have flush heads.
|
| |
 |
