LT Hinged Doors/Frames
Specifications
Hinged Door
 |
Sliding Door
 |
|
Materials: LT Hinged Doors/Frames
are fabricated of high quality, cold rolled carbon steel, free
of scale or rust and fully pickled. Exposed edges, corners and
surface areas are free of sharp edges and all workmanship is of
the highest quality as measured by the industry. |
|
Finish: All steel components shall be thoroughly cleaned and
phosphatized for rust resistance in a fi ve-stage pre-treatment
process. A high grade of polyester/epoxy powder paint is to be
applied electrostatically with a gloss reading of between 55 and
65. The finish shall have a salt spray rating of 250 hours or more. |
|
Header And Sill: The header is 16 guage steel, formed into a 1" wide
and 1-1/4" deep "C" channel formation having 9/16" formation on
the bottom leg of the header. The header is slotted to accept the
lock bar from the three locking system. The header is welded to
the door frame making it an integral part of the frame assembly. |
|
Door Frames: The door frames are 16 guage steel, formed into a 7/8"
channel formation with one leg of the channel being 1-7/32" and
the other leg being 7/8". The door frames are equipped with three (3)
hinges welded to each door frame on the 40" cabinets. Hinges
are recessed into the frame to ensure a tight uniform fit of the
doors. The door frames are welded to the header and sill, creating
a rigid welded frame assemble. Door frames are equipped
with four frame lugs that are welded to each door frame for 64",
76", 88" and two lugs welded to each door frame on the 40" cabinets. |
|
Frame Hooks: Frame hooks are 16 guage steel, formed into a 1-11/32" channel formation with one leg of the channel being 2" and
the other leg being 9/16". The frame hooks are inserted at the top
end of each corresponding upright in front of the cabinets and
door frames are temporarily secured. |
|
Hinged Door Clips: Hinged door clips are 12 gauge steel, formed into a 5/8" channel formation with one leg of the channel being
3/4" and the other leg being 15/16". The hinged door clips have
a 1/4-20 hole tapped on the 3/4" leg to secure the clip into each
side of the uprights and apply pressure to the frame lugs to
secure the door frame assembly. |
|
Hinges: Hinges are semi-concealed, four knuckle, tight-pin, 16
guage fully looped hinges that are welded to frames and riveted
to the door. There are three hinges per door on 64", 76", 88"
cabinets and two hinges per door on 40" cabinets. |
|
Doors: Doors are formed from 20 guage steel with a 3/4" flange
on the top and bottom. The doors are 1" thick with a channel
formation on the edges. The door strike on the left hand door is
hemmed for a smooth uniform edge. The doors are reinforced
with a full-length door stiffener that is 4" wide and 25/32" high.
The doors are designed in such a way to accept the three point
locking system. |
|
Handles: The cabinet has a plastic and steel recessed handle.
The handle has a built in lock and locks both door, making the
opening and closing of dual swing out doors easy. |
|
Three Point Locking System: The cabinet is equipped with a
secure three point locking system. The system consists of a
lock cam that secures the two doors together and two 5/8" x 1/8"
locking bars that locks the right door securely into the header
and sill. The left door is held securely by the right door. The
lock mechanism is operated by turning the right handle, and
the two lock bars operate smoothly with a cam and nylon silencers. |
|
Bolts & Nuts: Bolts & nuts consist of a sealed plastic bag with
1/4-20 phillips headed bolts with hex nuts. All bolts have flush
heads and are zinc or chrome plated.
|
|
